230
Sink with left/right drainer95х49cm

Avantgard
Series: Avantgard
Installation method: Inset
Cabinet widht: 70 cm
Dimensions: 95 x 49 cm
Bowl dimensions: 55 x 43 cm
Bowl depth: 21 cm
Mounting hole: 93 x 47 cm
Weight: 21 kg
Cast marble
0BGN 0BGN 0BGN
Select a color:Not selected
Select a hole option:Not selected
Number:

Options for drilling holes for a kitchen mixer, soap dispencer, pop-up button for automatic syphone and possible option for undermount installation

  • Two holes by installation of a kitche mixer and soap dispencer
  • Three holes by installation of a kitche mixer, soap dispencer and a third accessory
  • No possibility for drilling hole for kitche mixer and soap dispencer
  • drilled hole - Ø35
  • Pre-drilled hole
If there is no option for hole chosen, the sink will be delivered without a drilled hole
  • Specific structure of the material that reduces the noise from the water falling in the bowl;
  • High level of UV – resistance – the colors remain bright even by using the sink outdoor ;
  • Specific structure of the surface coating with high resistance of aggressive chemicals /except abrasives/. The smooth and non-porous coating prevents the formation of stains and overlays and provides a quick and easy cleaning;
  • Perfectly straight lines of the mounting surfaces;
  • A deep bowl on all models;
  • Pre-drilled holes for mixing battery or soap dispencer;
  • A big variety of modells and colors;
  • A high-level antibacterial protection due to the adding of silver ions to the material during the production.
  • High scratch - and impact resistance by FATGRANIT material;
  • Complectation with an /3 ½” siphon with overflow and a paper template for a presize cutting the montage hole on the countertop.

Cast Marble / Granixit Sinks

  • Some utensils have rough bottoms or sharp edges - use appropriate protective pad to keep the sink in a good condition;
  • Dropping of heavy or sharp objects in the sink may cause damages on the surface;
  • Do not place hot utensils with temperatures above 150 C° directly on the sink - risk of damage for the coating;
  • Do not use abrasives or sharp tools for cleaning the sink. The specific surface of the FAT sinks disables accumulation of spots or contaminations;
  • Daily clean out the sink using a household sponge and detergent, then rinse out with warm water;
  • Wipe dry the surface with a soft cloth or kitchen rolls – this prevents the formation of limestone overlays and stains;
  • Wih particularly resistant stains, treat the problem area with a sponge and detergent on chemical basis /e.g. for removal of lime scale, do not use abrasive cleaners/ and leave it work for a few minutes. Later on rinse out with warm water and wipe the sirface dry.

Fatgranit sinks

MAINTAINING A GRANITE SINK IS EASY IF YOU CLEAN IT REGUALARY WITH THE CLEANING DETERGENTS USUALLY USED IN YOUR HOUSEHOLD

Тhe longer the stains stand on the sink’s surface, the more difficult it would be to get rid of them.

Here are some recommendations from us for the remaining visible pollutions, traces of scratches, colourings or spots.

  • To remove grease deposits from the bottom and walls of the sink, use the standard dishwashing detergent and a soft sponge, then rinse thoroughly and dry;
  • To remove any other stains or scale deposits, apply anti-scale detergent evenly on the coated places, let it sit for about 5 minutes, then rinse thoroughly and dry.
  • To remove traces and scratches formed from metal utensils on the sink’s surface, as well as for treating especially stubborn stains, use abrasive dry or creamy household detergent. Wipe dry and apply the detergent on the affected area and let it sit for 5-10 minutes. With the abrasive side of a household sponge, rub the surface thoroughly using a circular motion(if necessary apply pressure). Rinse with water and wipe dry.
Warning: Do not use aggressive chemicals such as concentrated caustic soda, formic acid, etc. on this base, as well as highly corrosive preparations - there is a risk of surface damage or change of color.

Drilling of the pre-drilled holes for a mixing faucet and / or a dispenser for liquid soap:

Attention: drilling ALWAYS has to be done from the front side of the sink.
  • Using a hammer and drill tool, tap several times on the marked center;
  • Continue the knoking from the center of the hole to the periphery until the hole is well formed;
  • Clean and shape the hole with sandpaper or other suitable abrasive tool.

Installation of FAT Kitchen sinks

  • Use the paper tempate, draw the necesery place on the kitchen worktop;
  • Cut out the counter inside the marked outlines - the lines have to remain visible after cutting;
  • If necessary, drill the holes for a mixing baterry and / or a dispenser for liquid soap according to the instructions below;
  • Clean the contact surfaces with alcohol - those of the counter and the sink, and then apply a thin layer of transparent silicone;
  • Place the sink into the cuted hole and press it gently to the worktop using a heavy object;
  • Remove the silicone leaked around the edges and clean the rests;
  • After the final drying of silicon remove the pressing subject - the sink is ready for use.

Included in set:

  • Italian syphone Ø90 with overflow and additional connector for washing mashine/ dishwasher [ Syphone schema ]
  • paper template for worktop cutting
  • Certificates and instructions

The situation pictures are illustrative, the displayed accessories are not included in the complete set of the sinks.

229
233